Working principle: According to the principle of selective photopyrolysis, when shorted the action time of the laser, the laser energy diffuses less to the surrounding tissue. If the energy is limited to the target that needs treatment, the surrounding normal tissue can be protected, so the selectivity of treatment become stronger.The picosecond laser pulse width is only 1% of the traditional Q-switched laser. Under this ultra-short pulse width, the light energy is too late to be converted into heat energy, and there is almost no photothermal effect.When the laser energy is absorbed by the target, its volume will expand rapidly, and then be blasted and torn into pieces. "The picosecond laser is more powerful and complete in crushing pigment particles and less damaging the surrounding tissue." From the perspective of treatment, the effective rate can reach more than 94% (Ota nevus almost 100%). Application: Advantages: Treatment advantage: (1) High energy & short pulse duration: Energy can be released into the skin tissue in trillions of trillions of seconds, which can break down the pigment into smaller pieces. Compared with the traditional Q: switch laser, the pigment can be absorbed more easily and faster. (2) Low risk & painless: Since the pulse duration has been reduced a thousand times, skin damage has been reduced. Treatment is safer and less painful. (3) There was no anesthesia and inflammation during the treatment. (4) Fast： For tattoo removal, traditional Q: switching lasers usually require 6-8 treatments. With a picosecond laser, only 3-4 treatments are needed to completely remove it. (5) High performance: Using picosecond laser technology can completely remove tattoos and pigments. (6) Try any skin type, no obvious pigmentation after treatment. Laser type Pico second ND: YAG Laser Energy Level Single Mode: Max 400mj (532nm), Max 800mj (1064nm) Double Mode:Max 800mj(532nm), Max 1600mj (1064nm) Pulse width 750ps wavelength 1064nm,532nm,585nm(option),650nm(option) Frequency 1-10hz Spot size 2-10mm Dimension 107*50*118CM weight 115KG   Postoperative care 1.After treatment, there may be slight pain, white skin surface, epidermal bleeding, transient redness, swelling, blackening or even purpura. They can be absorbed by themselves without being too nervous.If there is a scab that will fall off on its own within 7--14 days, it should not be removed artificially, so as to avoid delaying skin healing and forming pigmentation. 2.Due to individual differences or climate changes, within a few days after treatment, the treatment area must not be in direct contact with water or other solutions to prevent infection. Try to eat less spicy food, excessive drinking, and smoking. 3.Very few individuals may have pigmentation on their skin after treatment, which usually subsides after 1-3 months. 4.After the operation, try to avoid activities in the sun and exposure, in order to avoid the production and increase pigmentation. Physical sunscreen works best 5.If any abnormal phenomenon is found after the operation, please go to the outpatient consultation and treatment in time. Exhibition We have sold a lot of products to all over the world. Our company participates in many exhibitions every year, such as Italy, Dubai, Spain, Malaysia, Vietnam, India, Turkey and Romania. There are some photos below: Package and delivery We package the machine in export standard metal box, and we use DHL, FedEx or TNT to delivery the machine to you by door to door service.                       Sunny Zhao                         Daria Jia    Sunny@sanhebeauty.com     Daria@sanhebeauty.net           +86 18813196949                    +86-18831450595

Working Therapy & Functions I-Cool Skin air cooler is intended to minimize pain and thermal injury during laser and dermatological treatments. It also provides temporary topical anesthetic relief during injections, tattoo application, tattoo removal, RF, laser hair removal and much more. The device can assist in a variety of applications and is particularly useful with cosmetic procedures. Appearance introduction 1. Compressors imported from Japan 2. Super wind speed blower 3. Independent noise reduction system 4. -30°C super-low temperature refrigeration 5. 200g super light cold air tube 6. Stepless speed regulation, temperature adjustment knob 7. One-key start-stop button Skin cooling device Ability to cool down to -30C (as measured inside machine) Minimise discomfort during cosmetic procedures 10 different air flow rates – customisable settings Eliminates need for expensive Cryo spray consumable Full day operation – no downtime Can be applied before, during, and after treatment Simple, easy to use, with useful tabletop glass Operator station introduction 1. Stepless speed regulation, temperature adjustment knob 2. Temperature  indication（-4℃~-30℃） 3. Strat-Stop button Laser source: Stormfiber-II air cooling system Controlling screen: 2.4 inch multi color screen Cooling power: 1500W Temperature range: -4℃~-30℃(adjustable) Refrigerants: R404A Fan speed: 1~8 level (adjustable) Treatment Pipe: 2.5m Pipe weight: 200g Outlet adaptor size: Φ6mm  Φ10mm  10mm*1.5mm LCD Screen: 2.4 Inch Storage platform size: 450*280*20mm Machine size: 610*380*750mm    50KG Package size: 820-500-930mm    74KG Power source: AC/100-240 V, 50-60 Hz，10A Safety Class: EN60601-1,TypeB MDD/MPG,Class I Adapters for Diode laser and IPL After inserted the connector assembly,The I-Cool could works with 808nm diode laser hair removal machine, co2 fractional laser machine, SHR machine, IPL machine and Nd yag laser machine...Suitable for all machines if patients feel pain and needs cooling procedure. Details Exhibition We have sold a lot of products to all over the world. Our company participates in many exhibitions every year, such as Italy, Dubai, Spain, Malaysia, Vietnam, India, Turkey and Romania. There are some photos below: Package and delivery We package the machine in export standard metal box, and we use DHL, FedEx or TNT to delivery the machine to you by door to door service. Contact with us:  Contact Person: Sunny Zhao, Alex Song E-mail: Sunny@sanhebeauty.com,   Alex@sanolasers.com Whatsapp: +86 18813196949  +86 15321516360

laser for hair removal 755 808 1064 diode machine Why choose our 755+808+1064nm diode laser machine ? More stable and higher powerful new golden welding laser module with German DILAS bars  . It can shot about 100 million times  . Double water filters , only change filters per 6 months and 1 year. And some old filters in some machines need change filter every month .  Save much maintainance cost and times for you . New Italy imported water pump replaced Chinese pump with better cooling system and more quiet duirng treatment . Those obvious difference will be found when your customers compare with some machines with Chinese water pump . Six way power supply replaced four way power supply, much higher and stable output . TEC cooling system , can control water temperature by yourself to keep 808 diode laser machine running continuously within 24 hours even in Summer . Same function as your A/C in  your house . Various power laser modules for your option , 300W 500W 600W 800W 1000W 1200W ... (6bars 10basr 12bars )  Single 808 wave, 755nm/808nm/1064nm double waves and triple waves for option . Why 755 808 1064 diode machine much better than SHR IPL technology ? As we known , the SHR IPL machine is traditional technology  , but most of treatment of them is for hair removal .   1) About 808nm diode laser is most professional technology for hair removal permanetely with painless .  2) It is most hot sale type product in Europe and America . 3) IPL SHR is really a old technology till now .   If you are distributor , you can tell your customers that diode laser machine can shot 20 million times and IPL SHR machine only can shot 300,000 times . It can help you save much money for repalcing new handpiece . One diode laser machine can do treatment times equel to 20 units IPL SHR machines . Treatment theory of 755 808 1064 diode machine Diode laser hair removal enables the light to penetrate deeper into skin and is safer than other lasers because it can avoid the melanin pigment in the skin’s epidermis. We can use it for permanent hair reduction of all color hairs on all 6 skin types, including tanned skin. Diode laser hair removal allows fast repetition rates up to 10Hz(10 pulses-per-second), with in-motion treatment, fast hair removal for big area treatment. Probe built in with excellent contact cooling technology, PAIN-FREE hair removal. Training video and manual will be sent with machine . Contact with us: Contact Person: Alex Song, Sunny Zhao E-mail: Alex@sanolasers.com   Sunny@sanhebeauty.net Whatsapp: +86 15321516360    +86 18813196949 FDA and Medical CE certificate

Pinxel Fractional RF Microneedle Device with Insulated needle/CE approved medical standard radio frequency rf machine for face Pinxel microneedle rf machine specification:   Main Function Acne scar, Skin Tightening and Whitening, Wrinkle Removal, Stretch Marks Removal Non-surgical Face Lifting Face Treatment Wrinkle Reduction Skin Tightening Skin Rejuvenation (Whitening) Body Treatment Scars Stretch Marks removal Pinxel microneedle machine application   System Type Mono&Bipolar RF Bipolar RF Frequency 2MHz Total RF treatment Level Up to Level 10 Dual Operation Mode Fractional RF Micro-needle Fractional RF Sub-Lative Max.Engery 50W Disposable Tip Micro-electrode needle Fractional RF tip Depth of Needle 0.5-3mm Display 10.4 inch LCD Switch Foot Switch 1. Pinxel-2 has four handles, Fractional RF handle (Non-invasive), Micro-needle RF handle (invasive), a cooling head, and a negative polar. 2. This machine is used for acne, scar, wrinkle, pigmentation removal, Skin Resurfacing, Large Pore Reduction and skin rejuvenation, face lifting, skin tightening. 3: This machine has Bipolar mode and Mono-polar mode two treatment mode, Most of China RF machine only has bi-polar mode. In Mono-polar mode, the RF energy is stronger. If using Mono-polar mode, the patient need to hold the negative polar handpiece   Contact with us: Contact Person: Alex Song, Sunny Zhao E-mail: Alex@sanolasers.com   Sunny@sanhebeauty.net Whatsapp: +86 15321516360    +86 18813196949  

About  us Our sales team are well trained and highly experienced in specific and specialized areas of product range. Thus providing customers with strong product knowledge and service support. We provide step by step operation instruction containing helpful tips and advice directly from our service team. From your initial contact with our sales team, to the delivery and use of our products, we offer  training, customer service, and technical support to meet your needs. All this helps ensure you get the best and most professional results every time. Picosecond nd yag laser system principle: The energy of  Picosecond laser can be absorbed by the blue and black melanin. The melanin will be fragmented so small that they can be metabolized by the lymphatic system or digested out of body. Thus the tattoo or other pigmentation will be removed without damage to the normal tissue. The treatment is safe and convenient without downtime and side effects. Preoperative skin care It could using 4% hydroquinone mixture and Vitamin A to do skin bleaching that could prevent skin from severe dehydration before surgery 3-4 weeks. for Type 1 or  there is no need to use these drugs if it is type 1 or type 2. It is necessary for skin type 3 and 4. If you want to carry out a large area of regeneration or grinding, you can use sedative drugs before treatment, so that make patients relax. One hour before surgery, clean the area with lidocaine (a local anesthetic), then cover the plastic wrap to promote absorption. In addition to the use of lidocaine before the treatment and gel , also need to increase the skin moisture to make laser treatment more refined to reduce the damage during treatment. Energy 100-800mJ adjustable Frequency 1-20Hz adjustable The energy is 100-300 mj, and the frequency is adjustable from 1-20Hz; The energy is 350-550 mj, the frequency is adjustable from 1-15Hz; The energy is 600-800mj, the frequency is 1-10Hz adjustable COUNT Current count,It will be cleared when you click once; click Count to display the total points used SIMMER ready signal；when SIMMER turn to green, you can click the working.                  WORKING When WORKING lights up, step on the foot switch to emit light Contact  us: Alex Song                       Sunny Zhao                          Ruby Mu  Alex@sanolasers.com   Sunny@sanhebeauty.net     ruby@sanhebeauty.net  +86 15321516360          +86 18813196949               +86 17633631496

Sano CE Approved hair Loss Treatment LLLT hair regrowth machine /Laser Hair Growth Laser hair regrowth machine prnciple: 1. Accelerate blood circulation to improve regeneration ability of collagen fibers and promote metabolism. 650nm laser and 625nm PDT can enhance the activity of Adenosine Triphosphate (ATP) of subcutaneous tissue. So 650nm laser and 625nm PDT help to enhance blood flow and make oxygen and nutrient send to the hair follicles, and 808nm laser will help solution penetration, as a result, it achieves the efficacy of halting the progression of hair loss. 2. Modulate the hair follicles 3. Regulate oil secretions 4. Promote scalp health, improve hair quality Laser + LED hair loss treatment Machine specification: Name Mild Laser + LED Hair Regrowth Machine Laser power output 650nm diode laser 320mw808nm IR laser 2200mw LED power output 630nm Red cool light 1000mw460nm Blue Cool light 1000mw 580nm Yellow Cool light 2000mw Treatment Time 0-60min Pulsing time range 1-10s (adjustable) Pulsing delay range 0-10s (adjustable) Input power 200w LCD Screen 8-inch multi-color touch screen Main accessories Hair & Scalp AnalyzerMicro-current Comb Oxygen Spray pen Medicine Sprayer The feature of this machine: 1.Five kinds of wavelength (808nm，650nm，630nm，580nm, 460nm ). 2.Lasers and LED cold laser mixed in one helmet. Most of the laser hair regrowth machine in the market only has the 650nm laser. Or only LED. But our SH650-1 hair regrowth system combines two kinds of lasers and 3 kinds of LED. 3. Laser and LED lights are imported from Japan. We use higher quality Japanese laser and LED light. Energy is stable, lifetime is longer. 4.Oxygen spray pen. Used for clean and sterilize scalp. 5.Medicine spray pen. It can help the hair regrowth medicine like Minoxidil average on the scalp. 6.Micro-current massage comb. To help medicine absorbed faster, and do massage to the scalp. 7.Professional hair & Scalp analyzer. It can do the analysis for hair and scalp, save 2000 patients’ information, before and after photos (It has a camera to take photos), and print analysis report. 8. The system is very easy to operate. The work time for the 5 wavelengths is adjusted separated. Most the machine in the market has no Medicine spray pen, Micro-current comb, Oxygen sprayer, also no Hair& Scalp analyzer. SH-650 treatment is safety and painless: SH-650 uses low level laser module as a light source that does not have a thermal component so they will NOT vaporize or burn tissue. Our lasers are considered a Class 1M cosmetic device and are rendered safe for topical use by the . FAQ The patient will feel uncomfortable use this machine or not? No, this machine use low level laser and LED lights. The energy is not very strong, and this technology is US approved, it's very safe to use. What's more, under the helmet, it has Air spray, they can make patient feel very comfortable. What is a oxygen spray pen, what can I put in it? oxygen spray pen is used for clean and sterilize for the scalp, you should put normal saline in it, It will spray the saline as gas, suitable for the cleaning and disinfection. What are the LED lights' functions: Red light can make cell activity increased, promote cells metabolism, accelerate the blood circulation, control oil secretion. Blue light can kill hair pathogenic bacteria effectively, kill the hidden fungi and mites deep in the hair follicles. Yellow light with wavelength 580 nm can ease and treat sensitive skin effectively. What is the parameter setting The power of the 650nm is fixed, because 650nm is the main energy course, we have to guarantee the results, LED time setting, usually we suggest to set them on time: 5-10s, . They are adjuvant treatment, 808nm laser, power:6. on time 8-10s, off time 0-2s. 650nm laser: on time: 10s, off time: 0s. Contact with us: Contact Person: Alex Song, Sunny Zhao E-mail: Alex@sanolasers.com   Sunny@sanhebeauty.net Whatsapp: +86 15321516360    +86 18813196949  

1. Pinxel-2 has four handles, Fractional RF handle (Non-invasive), Micro-needle RF handle (invasive), a cooling head, and a negative polar. 2. This machine is used for acne, scar, wrinkle, pigmentation removal, Skin Resurfacing, Large Pore Reduction and skin rejuvenation, face lifting, skin tightening. 3: This machine has Bipolar mode and Mono-polar mode two treatment mode, Most of China RF machine only has bi-polar mode. In Mono-polar mode, the RF energy is stronger. If using Mono-polar mode, the patient need to hold the negative polar handpiece Advantages: 1: It has insulated and non-insulated needle tips, two needle types for the doctor to choose. (25 pins insulated, 25 pins non-insulated, 49 insulated and 49 pins non-insulated needle tip) 2: The depth of the needle are adjustable on screen, 0.5mm-3mm. 0.5-1.0mm used for eye around, 1.0-2.0mm used for face treatment. 2.0-3.0mm used for body treatment. 3: There are 25 pins, 49 pins needle tips, insulated tips and non-insulated tips. 4: It uses Korea imported step motor. The needles are stronger, can come into skin more easily. In China, only Sanhe use this kind of motor. 5: It has a cooling head. Used for after-treatment care. Most other similar machines have no cooling head Contact with us: Contact Person: Alex Song, Sunny Zhao E-mail: Alex@sanolasers.com   Sunny@sanhebeauty.net Whatsapp: +86 15321516360    +86 18813196949  

sano Microneedling RF platform face lifting skin rejuvenation Microneedle RF Pinxel-2 RF Microneedling is the world’s first RF microneedling platform. With the ability to add multiple handpieces*, Pinxel-2 RF offers more versatility than other leading RF Microneedling products. Designed to maximize patient efficacy, experience and your business, Pinxel-2 RF boasts advanced ergonomic, interface, safety and treatment delivery features. Pinxel-2 RF is manufactured by the global leader in RF microneedling technology From the SmartRF handpiece’s , to the exclusive post-treatment protocol, the comfort, results and unique experience your patients can expect from Pinxel-2 RF microneedling are unmatched. The 25 or 49 gold-coated needles of the Smart RF are precisely delivered at a specified depth to provide immediate results with continued improvement over time and a virtually painfree, zero social downtime treatment. Only the Pinxel-2 RF pairs every treatment with the most innovative sheet mask technology available – the Microcurrent Dual Face Mask system. This two mask system soothes skin and eliminates redness. After the pinxel-2 RF treatment, a wet enriching Mask infused with antioxidants, vitamins, moisturizing and anti-inflammatory properties is applied to the skin. Contact with us: Contact Person: Alex Song, Sunny Zhao E-mail: Alex@sanolasers.com   Sunny@sanhebeauty.net Whatsapp: +86 15321516360    +86 18813196949

1. Pinxel-2 has four handles, Fractional RF handle (Non-invasive), Micro-needle RF handle (invasive), a cooling head, and a negative polar. 2. This machine is used for acne, scar, wrinkle, pigmentation removal, Skin Resurfacing, Large Pore Reduction and skin rejuvenation, face lifting, skin tightening. 3: This machine has Bipolar mode and Mono-polar mode two treatment mode, Most of China RF machine only has bi-polar mode. In Mono-polar mode, the RF energy is stronger. If using Mono-polar mode, the patient need to hold the negative polar handpiece Advantages: 1: It has insulated and non-insulated needle tips, two needle types for the doctor to choose. (25 pins insulated, 25 pins non-insulated, 49 insulated and 49 pins non-insulated needle tip) 2: The depth of the needle are adjustable on screen, 0.5mm-3mm. 0.5-1.0mm used for eye around, 1.0-2.0mm used for face treatment. 2.0-3.0mm used for body treatment. 3: There are 25 pins, 49 pins needle tips, insulated tips and non-insulated tips. 4: It uses Korea imported step motor. The needles are stronger, can come into skin more easily. In China, only Sanhe use this kind of motor. 5: It has a cooling head. Used for after-treatment care. Most other similar machines have no cooling head Contact with us: Contact Person: Alex Song, Sunny Zhao E-mail: Alex@sanolasers.com   Sunny@sanhebeauty.net Whatsapp: +86 15321516360    +86 18813196949  

Working Theory High Intense Focused Ultrasound is the newest technology for weight loss, which is comparable with liposuction. Meanwhile it is more safe and painless than Liposuction. HIFU head can delivers the HIFU energy to the specific depth of the subcutaneous tissue layer.The energy after conduction through the mechanical, cavitation and thermal effects , can destroy the fat cells. Then by limiting the energy value, conduction distance and machine's power. Making only low density of fat cells are easy to be damaged，And the target area and the surrounding tissue, such as: skin, blood vessels, nerves and connective tissue, etc. will not be harmed. This result is also confirmed by histological examination——Fat cells dissolved, meantime the surrounding tissue did not appear damage.The body destroy and excluded the fat cells through the metabolism from the body, so as to achieve weight loss, body sculpting effect. Advantages （1）230khz HIFU and do the treatment on Abdomen, thighs and Buttocks； （2）Single Pulse Mode：Adjustable Energy；Easy to Operate； （3）Water cycle cooling System: energy conversion fast, no hot water circulation； （4）HIFU head is made of special materials: can ensure the energy work on the fat cells accurately and completely;Special cooling gel conduction：Which can penetrate the fat cells quickly； （5）Precise energy setting: penetration depth control (maximum 1.2cm), It is more safe for adipose tissue and dissolved fat, safer;40kHz can reduce the fat on arms legs and buttocks； （6）2MHz Bi-polar rf had can be used for face lift；  (7)Cooling head can do the semi-conduction cooling after and before treatment Main interface: SaluShape body slimming and face lifting machine Specification andle type Frequency Energy level Treatment mode Tip size Focused ultrasound 230khz 1-30 degree pulse mode D42mm Ultrasound cavitation 40khz 1-10 degree Continuous mode D50mm Bipolar RF 2Mhz 1-30 degree Continuous mode D8mm, Distance:15mm Input Power 400W Focus Depth 12mm Cooling head temperature -5°C-5°C Treatment life span of handpiece 500,000 shots Machine size 550X360X1175mm Package dimension 705*515*1130mm Machine weight 38kg Package weight 63kg Power requirements 110V-240V,10A single phase Environmental requirements +15C-30C, 80% humidity   SaluShape Body Slimming And Face Lifting Machine effect Exhibition We have sold a lot of products to all over the world. Our company participates in many exhibitions every year, such as Italy, Dubai, Spain, Malaysia, Vietnam, India, Turkey and Romania. There are some photos below: Package and delivery We package the machine in export standard metal box, and we use DHL, FedEx or TNT to delivery the machine to you by door to door service. Contact with us:  Contact Person: Sunny Zhao, Daria Jia E-mail: Sunny@sanhebeauty.com,   Daria@sanhebeauty.net Whatsapp: +86 18813196949  +86 18831450595

laser and led hair loss treatment machine Technologies for HR-II: 1.650nm diode laser 2.808nm infrared laser 3.630nm red PDT 4.460nm blue PDT 5. 580nm yellow PDT 6. PDT&EMS comb 7. Single head Oxygen Jet—for epidermis 8. Oxygen gun—Oxygen spray Characteristics: 1. Stimulate the scalp, anti-hair loss, no harm, no consumables, no drug side effects 2. Six in one hair mask 3. Accurate light dose, output stability, long life 4. For male and female hair loss, six kinds of automatic programming, used in Different stages of hair loss 5. Multi-hand designed 6. Dual-color interactive touch Applications: 1. Seborrheic, pathological, physical, chemical and obesity hair loss 2. Catagen and telogen hair loss 3. Follow-up care after hair transplant 4. Improving the hair quality The feature of this machine: 1.Five kinds of wavelength (808nm，650nm，630nm，580nm, 460nm ). 2.Lasers and LED cold laser mixed in one helmet. Most of the laser hair regrowth machine in the market only has the 650nm laser. Or only LED. But our SH650-1 hair regrowth system combines two kinds of lasers and 3 kinds of LED. 3. Laser and LED lights are imported from Japan. We use higher quality Japanese laser and LED light. Energy is stable, lifetime is longer. 4.Oxygen spray pen. Used for clean and sterilize scalp. 5.Medicine spray pen. It can help the hair regrowth medicine like Minoxidil average on the scalp. 6.Micro-current massage comb. To help medicine absorbed faster, and do massage to the scalp. 7.Professional hair & Scalp analyzer. It can do the analysis for hair and scalp, save 2000 patients’ information, before and after photos (It has a camera to take photos), and print analysis report. 8. The system is very easy to operate. The work time for the 5 wavelengths is adjusted separated. Most the machine in the market has no Medicine spray pen, Micro-current comb, Oxygen sprayer, also no Hair& Scalp analyzer. Functions: 1. Accelerate blood circulation to improve regeneration ability collagen fibers and promote metabolism 2. Modulate the hair follicles 3. Regulate oil secretions 4. Promote scalp health, improve hair quality 5. Promote nutrient absorption Technologies for hair mask: 1. 630nm red PDT 2. 580nm yellow PDT 3. 470nm blue PDT 4. 650nm red laser 5. 808nm infrared laser 6. Oxygen therapy Treatment results Contact with us: Contact Person: Alex Song, Sunny Zhao E-mail: Alex@sanolasers.com   Sunny@sanhebeauty.net Whatsapp: +86 15321516360    +86 18813196949

Working Theory Before operation using，have a temporary anesthesia. Powerful cooling to -30℃.The 1500W high-power compressor provided by Danfoss ensures the system can work continuously for long periods of time.（When the wind speed level is 4, The machine can work for 2 hours the minimum temperature）.High-speed fans have a strong cooling effect, also 6 levels  wind speed can meet the needs of different treatments.Automatic defrost is the best performance for cooling.The self-draining system ensures the safe and cleaning of machine.The supporter for cooling make the operation more comfortable. Best partner After inserted the connector assembly, The I-Cool could works with 808nm diode laser hair removal machine, co2 fractional laser machine, SHR machine, IPL machine and Nd yag laser machine...Suitable for all machines if patients feel pain and needs cooling procedure. Advantage: 1.High power compressor makes the system work for long time continuously (Lowest temperature can keep 2 hours under 4 level fan speed) 2. High speed fans makes air emitting strong for better cooling result, 6 degree cooling fan speeds for various treatment. 3. Self defrosting system for best cooling performance 4.Self water drainage system make safe and cleaning performance 5. Fuse supporter make the procedure comfortable Laser source: ICOOL air cooling system Controlling screen: 5 inch multi color touch screen Power: 1000W Temperature range: -4℃~-30℃(adjustable) Fan speed: 1~6 (adjustable) Defrosting time: 15s Power requirement: 110V,50hz,3A, 220V,50hz, 3A Net weight: 62kg Treatment Fuse: 2 meters Fuse supporter: 3 joint supporter Dimension of system: 810*400*845mm Package size: 915*515*1050mm Operation This machine can be used with 808 laser, IPL, 980 laser, CO2 laser, RF machine, Can reduce the pain and temperature, avoid the scald. 1. Before treatment, can blow the treatment area for 2 minutes, cooling that 2. The treatment head should target to the light outlet when you do the laser treatment. 3. If there is no adapter with the optical device, then the face treatment, the outlet should be tilted along the patient's forehead to the direction of the chin for treatment, so that patients more comfortable. CE Certificate Machine in treatment Exhibition We have sold a lot of products to all over the world. Our company participates in many exhibitions every year, such as Italy, Dubai, Spain, Malaysia, Vietnam, India, Turkey and Romania. There are some photos below: Package and delivery We package the machine in export standard metal box, and we use DHL, FedEx or TNT to delivery the machine to you by door to door service. Contact with us:  Contact Person: Sunny Zhao, Daria Jia E-mail: Sunny@sanhebeauty.com, Daria@sanhebeauty.net Whatsapp: +86 18813196949  +86 18831450595